000-109無料問題集「IBM Virtualization Technical Support for AIX and Linux

質問 1

A new NPIV VIO client is being built. How can the administrator log all virtual Fibre Channel adapters into the SAN so the WWPNs are visible for disk mapping?

（A）Boot the LPAR to SMS and run the configure boot device.

（B）Boot the LPAR into the Open Firmware prompt and run ioinfo command.

（C）Boot the LPAR normally, use the lsmap -all -npiv command on the VIO server to check it has logged in.

（D）Boot the LPAR from a NIM server and access a maintenance shell.

正解：D 解答を投票する

質問 2

Following the reboot of one VIO server (VIOS) in a redundant configuration, a client is showing failed disk paths on some channels.
What is the most likely reason the disk paths have failed?

（A）MPIO drivers have not been installed on the client.

（B）VIOS Fibre Channel adapters have created a private loop as the attribute init_link has not been set.

（C）vSCSI and disk attributes vscsi_err_recov, vscsi_path_to & hcheck_interval have not been configured.

（D）Disk attributes on VIOS for the reserve policy on the disk is not set to no_reserve.

正解：C 解答を投票する

質問 3

An architect requires Active Memory Sharing (AMS) to be implemented for a new AIX environment. Which of the following are minimum requirements in order to implement AMS?

（A）PowerVM Standard Edition, POWER7 Hardware, HMC version 7.7.1

（B）PowerVM Enterprise Edition. POWER6 Hardware, AIX 6.1 TL3

（C）PowerVM Standard Edition, HMC version 7.3.5, VIO Server version 2.1 FP21

（D）PowerVM Enterprise Edition, AIX 6.1 TL4, redundant storage

正解：B 解答を投票する

質問 4

An administrator has installed a Linux LPAR using virtual storage and virtual networking on a POWER7 system and is attempting to DLPAR additional memory into the LPAR. They see the following error message during the DLPAR operation.

Which action will resolve this issue?

（A）Upgrade the version on Linux to support memory DLPAR.

（B）Add the HMC to the /etc/hosts file.

（C）Install the IBM Installation Toolkit for Linux

（D）Configure a network on the same subnet on the HMC.

正解：C 解答を投票する

質問 5

A customer is in the process of configuring a redundant pair of VIO Servers. They need to test that SEA failover has been correctly enabled. Which command can the padmin UserID use (on the active SEA, ent4) to manually force an SEA failover event?

（A）chdev -l ent4 -attr ha_mode=failed

（B）chdev -dev ent4 -attr ha_mode=standby

（C）chdev -d ent4 -attr ha_mode=Active

（D）chdev ent4 -attr ha_mode=True

正解：B 解答を投票する

質問 6

An architect is considering whether to specify vSCSI or NPIV for the rootvg disks in a new virtualized environment. Storage is to be provided by an IBM San Volume Controller (SVC) and controlled using SDDPCM.
Which of the following is an advantage of using vSCSI technology instead of NPIV?

（A）vSCSI provides active/active multi pathing, allowing I/O requests to be distributed between dual VIOS partitions

（B）Queue depths higher than 20 for rootvg disks are supported with vSCSI.

（C）vSCSI allows for client level logical volume mirroring for rootvg, providing enhanced protection.

（D）Support for vSCSI devices is included within base AIX, removing the need to install device drivers at the client level.

正解：D 解答を投票する

質問 7

An administrator needs to add additional LPARs to a Power 770 server, but all of the
available memory on the system is currently assigned to existing LPARs and is continually utilized.
What solution can the administrator implement on the system to add the LPARs?

（A）Active Memory Expansion

（B）Virtual Memory Management

（C）Active Memory Compression

（D）Weighted Memory Allocation

正解：A 解答を投票する

質問 8

Which interface must be used to provide virtualization of tape library devices to client LPARs?

（A）USB

（B）Virtual Fibre Channel

（C）Virtual SCSI

（D）LTO

正解：B 解答を投票する

質問 9

An administrator is attempting to remove a virtual adapter from an AIX partition using an HMC running V7R7.2. The DLPAR operation is failing with the following message:
"Virtual adapters that are marked as required cannot be dynamically removed from the partition. Please change your adapter selections and try the operation again."
How can the administrator remove the virtual adapter while minimizing any downtime?

（A）Modify the active properties for the partition so that the adapter is not required for partition activation and repeat the DLPAR operation.

（B）Modify the last activated partition profile so that the adapter is not required for partition activation and repeat the DLPAR operation.

（C）Select the 'Force' option when performing the DLPAR operation.

（D）Remove the virtual adapter from the partition profile and reactivate the partition.

正解：B 解答を投票する

質問 10

Which of the following statements is true when considering Active Memory Sharing?

（A）Each paging VIO server partition must have a single dedicated paging device.

（B）Only physical hard disks are supported as paging devices.

（C）Only one paging VIO server partition is supported in each system.

（D）Every partition in the shared memory pool requires its own dedicated paging device.

正解：B 解答を投票する

000-109 無料問題集「IBM Virtualization Technical Support for AIX and Linux - v2」

弊社を連絡する

関連リンク

トップ試験