7004-1無料問題集「Avaya Communication Server 1000 for Avaya Aura® Maintenance」

質問 1

Click the Exhibit button.

A customer has asked if the Communication Server 1000 RIs. 7 x system can route anyone that dial an unassigned number in the customer's DID range to the Attendant.
In reviewing the current configuration as shown in the exhibit, what do you conclude?
(Choose two)

（A）NET_DATA Attendant and tie trunk users are receiving an overflow tone

（B）only internal station users are routing to the Attendant

（C）all caller types are receiving an overflow tone

（D）internal station users and non tie line users are routing to the Attendant

正解：D 解答を投票する

質問 2

Click the Exhibit button.

A Communication Server 1000 RIs. 7 x customer is adding a new Human Resource department with eight IP telephone users. The customer has asked for the telephones to be programmed with consecutive Directory Number (DNs) from their DID range (20002099).
Which number sequence is available to meet the customer's requirements?

（A）2050 - 2057

（B）2010 - 2017

（C）2001 - 2008

（D）2091 - 2098

正解：D 解答を投票する

質問 3

You are using Element Manager to program a Route List Index (RLI).
Which Electronic Switched Network (ESN) parameters must you define to be able to successfully program an RLI?

（A）Optimal Route (OPRT)

（B）Maximum number of route lists (MXRL)

（C）Minimum number of route lists (MNRL)

（D）Routing Control (PTCL)

正解：B 解答を投票する

質問 4

Your customer has a Communication Server 1000 RIs. 7 x system equipped with System Errors and Events Lookup pack 245 that provides the ability to display system messages on screen.
When a system message in received, which procedure should you use to look it up and display it on the screen?

（A）Enter errcde followed by the system error code and <cr>. For example, errcde bug4080<cr>

（B）Enter the system error number followed by <cr> For example, bug4080<cr>

（C）Enter err followed by the system error code followed by <cr>. For example, err bug4080<cr>

（D）Enter bug followed by the system error code and <cr>. For example, bugerr4080<cr>

正解：D 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 5

The Allow Last Digit Repeat function permits a repeated last digit of an ESDN to terminate the call immediately, similar to pressing the octothorpe (#) key. This prevents an ESA call from being dropped if the last ESDN digit is accidentally dialed again, but also processes the call immediately, rather than allowing an extended pause waiting for an additional digit.
To use this feature, which task must you complete first?

（A）enable Misdial Prevention

（B）enable ESDN Digit Repetition

（C）Create an Emergency Service Directory Number

（D）enter a Misdial Delay

正解：A 解答を投票する

質問 6

An enterprise has a network with Communication Server 1000E systems running RIs 7 x IP Peer Network. For this network, when are the Digital Signal Processor (DSP) resources required?

（A）when interworking is necessary to third-party SIP-enabled products

（B）when interworking is necessary to third-party H.323-enabled products

（C）when a compressed media channel is required without circuit switching

（D）when it is necessary to transcode between IP and circuit-switched devices

正解：D 解答を投票する

質問 7

Given the following network characteristics:
three Communication Server 1000 RIs. 7 x systems IP Peer Networking required DN uniqueness cannot be maintained route calls using site Location Codes (LOCs)
Which type of dialing plan is recommended for this call routing scenario?

（A）Coordinated Dialing Plan (CDP)

（B）Uniform Dialing Plan (UDP)

（C）Network Attendant Numbering Plan

（D）Flexible Numbering Plan (FNP)

正解：D 解答を投票する

7004-1 無料問題集「Avaya Communication Server 1000 for Avaya Aura® Maintenance」

弊社を連絡する

関連リンク

トップ試験