D-PDC-DY-23 無料問題集「EMC Dell PowerSwitch Data Center Deploy 2023」

（A）Terminates established BGP sessions for the specified ASN (64567)

（B）Maintains existing BGP sessions but no longer establishes new ones

（C）Stops any traffic from being sent on the physical interface used to reach neighbor 192.168.200.1

（D）Terminates any established BGP sessions for the specified neighbor

（A）239.0.0.6

（B）224.0.0.6

（C）224.0.0.5

（D）239.0.0.4

（A）To assist with load balancing

（B）To avoid the need to configure multi-exit discriminators

（C）To reduce the number of hops

（D）To minimize the needed compute and memory resources

（A）Device is a reference clock.

（B）Device is unsynchronized.

（C）Device has the lowest synchronized accuracy.

（D）Device has the highest synchronized accuracy.

（A）OSPF Packet type 1 - a) Link State Request
OSPF Packet type 2 - f) Link Local Address
OSPF Packet type 3 - e) Link State Update
OSPF Packet type 4 - d) Link State Acknowledgement
OSPF Packet type 5 - c) Database Description

（B）OSPF Packet type 1 - a) Link State Request
OSPF Packet type 2 - f) Link Local Address
OSPF Packet type 3 - c) Database Description
OSPF Packet type 4 - d) Link State Acknowledgement
OSPF Packet type 5 - e) Link State Update

（C）OSPF Packet type 1 - a) Link State Request
OSPF Packet type 2 - b) Hello
OSPF Packet type 3 - c) Database Description
OSPF Packet type 4 - d) Link State Acknowledgement
OSPF Packet type 5 - e) Link State Update

（D）OSPF Packet type 1 - a) Link State Request
OSPF Packet type 2 - f) Link Local Address
OSPF Packet type 3 - b) Hello
OSPF Packet type 4 - d) Link State Acknowledgement
OSPF Packet type 5 - c) Database Description

（A）no switchport mode trunk

（B）no switchport trunk allowed vlan 40

（C）switch pert mode trunk no allow vlan 40

（D）switchport trunk delete vlan 40

（A）S2(config)# router bgp 64507
S2(config-router-bgp-64507)# peer-as 64507
S2(config-router-bgp-64507)# neighbor 192.168.32.1
S2(config-router-neighbor)# update-source loopback 0
S2(config-router-neighbor)# no shutdown

（B）S2(config)# router bgp 64507
S2(config-router-bgp-64507)# remote-as 64507
S2(config-router-bgp-64507)# neighbor 192.168.32.1
S2(config-router-neighbor)# update-source loopback 0
S2(config-router-neighbor)# no shutdown

（C）S2(config)# router bgp 64507
S2(config-router-bgp-64507)# neighbor 192.168.32.1
S2(config-router-neighbor)# remote-as 64507
S2(config-router-neighbor)# update-source loopback 0
S2(config-router-neighbor)# no shutdown

（D）S2(config)# router bgp 64507
S2(config-router-bgp-64507)# neighbor 192.168.32.1
S2(config-router-bgp-64507)# remote-as 64507
S2(config-router-bgp-64507)# update-source loopback 0
S2(config-router-bgp-64507)# no shutdown

（A）ABR

（B）Backbone router

（C）ASBR

（D）Designated router

（A）The first-hop router is used to provide routing between the source and receiver.

（B）The node is used to provide (S,G) across a Layer 3 boundary.

（C）The location PIM sends traffic before invoking SPT.

（D）The node is used to provide (*,G) on a Layer 2 shared segment.

（A）Downlinks must be configured in equal pairs in both switches

（B）All switches should have extra capacity to accommodate a switch failure

（C）Uplinks must be configured in equal pairs in both switches

（D）Some performance degradation may occur due to a short downtime