HP2-T23無料問題集「HP Supporting Industry Standard Server Solutions」

質問 1

How do you boot into Intelligent Provisioning on a ProLiant Gen8 server?

（A）Through the Array Configuration Utility (ACU) in offline mode

（B）Through a Scripting Toolkit server configuration script

（C）By pressing the F10 button during POST

（D）By pressing the F9 button during POST

正解：C 解答を投票する

質問 2

What are some general requirements that must be met to update Virtual Connect firmware? (Select three.)

（A）Multiple instances of the Virtual Connect Support Utility (VCSU) must be run, with multiple clients, to access an enclosure faster.

（B）The correct deployment order must be set.

（C）The enclosure must not be part of a domain.

（D）The VC firmware must not be flashed before the configuration is backed up.

（E）The VC domains must not be in Maintenance Mode, so the firmware updates have direct access.

正解：B、C、D 解答を投票する

質問 3

Which tool can report the amount of life remaining in an HP solid state drive (SSD)?

（A）Array Diagnostic Utility

（B）Storage Management Utility

（C）SMARTSSD Wear Gauge

（D）Intelligent Provisioning

正解：C 解答を投票する

解説: (JPNTest メンバーにのみ表示されます)

質問 4

You cannot get to the network from any of the server blades in a c7000 enclosure with 10GbE Pass-Thru modules.
What should you verify first for proper connectivity to the network?

（A）Correct SFPs are installed

（B）External switch set to half duplex

（C）Interconnect link between the Pass-Thru modules

（D）External switch supports at least Gigabit speed

正解：C 解答を投票する

質問 5

Why is it considered a best practice to use tools such as HP Smart Update Manager (SUM) and Virtual Connect Support Utility (VCSU) to deploy firmware components?

（A）These tools support cross-platform deployments

（B）These tools are compatible with all versions of firmware

（C）These are the only tools that work with Virtual Connect Enterprise Utility (VCEU).

（D）These tools check dependencies and limitations.

正解：D 解答を投票する

質問 6

What should be installed on a ProLiant Gen8 server to display operating system information within the iLO 4 GUI?

（A）HP Management Agents

（B）System Management Home Page

（C）Agentless Management Service

（D）ProLiant Support Pack

正解：C 解答を投票する

質問 7

From which location does Active Health collect data?

（A）iLO

（B）Event Log

（C）IML

（D）SMH

正解：A 解答を投票する

質問 8

A support engineer is troubleshooting a ProLiant DL360p Gen8 server.A hard disk m a four drive RAID 5 set has failed.The engineer notices that on three of the drives, the LEO labeled D on the exhibit is on.What does the condition indicate?

（A）The drive failure has corrupted three drives in the RAID set. The array must be rebuilt and data restored from backup

（B）The drives should not be removed when this LED is illuminated

（C）Hot swapping of the failed drive is not supported in this condition

（D）The LED indicates failure and predictive failure alerts. Two additional drives in the RAID set are at risk of failing and need to be replaced

正解：B 解答を投票する

質問 9

A ProLiant DL 380 G7 server has a failure indicating that memory slot DIMM 1 has errors To troubleshoot the problem, you exchange the memory modules in slots 1 and 2 with each other.
Now you have a memory error indicating that memory slot 1 has errors, and an amber LED next to slot 1 is lit.
What should you do?

（A）Run the ECC memory test in the diagnostics to correct the errors

（B）Replace the memory module in slot 1 because it is definitely bad

（C）Replace the system board and rerun the memory diagnostics.

（D）Replace both memory modules in slots 1 and 2

正解：B 解答を投票する

質問 10

Which HP tool is used to configure NIC teaming on a Windows server?

（A）RBSU

（B）Insight Control

（C）ORCA

（D）PCM+

正解：B 解答を投票する

HP2-T23 無料問題集「HP Supporting Industry Standard Server Solutions」

弊社を連絡する

関連リンク

トップ試験