NACE-CIP2-001無料問題集「NACE Coating Inspector Level 2」

質問 1

You are the NACE Inspector on a project where a stationary floating structure is being coated and you notice a self-smoothing anti-fouling coating has been specified.
This is not a good choice because:

（A）The floating structure is stationary

（B）It will result in a very slippery surface

（C）It doesn't contain biocide

（D）It contains biocide

正解：D 解答を投票する

質問 2

Generally for safety considerations, waterjetting hose connections use

（A）a long wand.

（B）filters.

（C）a whip-lock device.

（D）an oil/water separator.

正解：C 解答を投票する

質問 3

Which concrete smoothing technique involves scrubbing a mixture of cement mortar over the concrete surface using ai cement sack, gunny sack, or sponge rubber float?

（A）Acid etching

（B）High-pressure water washing

（C）Sacking

（D）Stoning

正解：C 解答を投票する

質問 4

When performing a hardness test on a coating which has elastic properties the inspector is likely to likely to observe:

（A）A very high reading

（B）No difference from any other coating

（C）A very low reading

（D）Cold flow or creep

正解：D 解答を投票する

質問 5

A reinforced coating is

（A）equally resistant to movement and impact as a non-reinforced coating.

（B）more resistant to movement, abrasion, and impact than a non-reinforced coating.

（C）less resistant to movement, abrasion, and impact than a non-reinforced coating.

（D）equally resistant to abrasion and impact as a non-reinforced coating.

正解：B 解答を投票する

質問 6

Because a NACE Level 2 Inspector has been trained in specific destructive tests, it is up to the Inspector to decide if and when a destructive test is required.

（A）False

（B）True

正解：A 解答を投票する

質問 7

You are working as the only in-house NACE Level 2 Inspector in a shop setting when an independent 3 rd party NACE Level 3 Inspector, representing the owner, presents you with a copy of a Non Conformance Report (NCR) he has written for a NACE2/SSPC SP 10 centrifugal blast which you had previously approved.
Your FIRST preferred course of action is to:

（A）Review the NCR with the other Inspector

（B）Request a re-blast of the item in question

（C）Verbally challenge the NCR

（D）Consult your supervisor

正解：D 解答を投票する

質問 8

You are a NACE Level 2 in-house inspector working in a shop. Your in-house requires you to perform a sleeve test to test for soluble salts; however the 3 rd party NACE Level 3 inspector, the owner, has a san smart meter and has achieved a very different result and has rejected the pre-cleaning.
Your FIRST course of action is to:

（A）Advise the other inspector he is using an incorrect method

（B）Review the specification with the other inspector to see what method was specified

（C）Redo the pre-cleaning based on the other inspectors results

（D）Advise your QC Manager to change the ITP to the use of the salt smart meter

正解：B 解答を投票する

質問 9

In powder coatings, when the particles of powder begin to flow but are not fully liquid, they are in what stage?

（A）Gel stage

（B）Wetting stage

（C）Flow stage

（D）Cure stage

正解：C 解答を投票する

質問 10

On pipelines, which coating is identifiable by its distinct colors, usually light blue, green, or grey?

（A）Coal Tar Enamel

（B）Heat-shrink sleeves

（C）Liquid epoxies

（D）Concrete

正解：C 解答を投票する

NACE-CIP2-001 無料問題集「NACE Coating Inspector Level 2」

弊社を連絡する

関連リンク

トップ試験