NCSC-Level-1無料問題集「Nutanix Certified Services Consultant (NCSC): Level 1」

質問 1

A customer has an ESXi Cluster with two 10GbE NICs on each node with the following requirements:
* Solution must follow Nutanix Best Practices
* Network configuration should be redundant
* A vSphere Standard Switch must be utilized
Which load balancing method should be used?

（A）Route based on source MAC hash

（B）Route based on originating port ID

（C）Route based on physical NIC load

（D）Route based on IP hash

正解：B 解答を投票する

質問 2

A customer wants to use NIC teaming on an ESXi host using a vSphere Standard Switch configured with the Route based on physical NIC load load balancing option. The customer does not see the option when editing the Teaming and Failover settings for the switch.
How should the consultant resolve this issue?

（A）Add another physical NIC to the team.

（B）Add a vSphere Distributed Switch

（C）Install a vCenter server to manage the switch

（D）Change the load balancing option on the switch.

正解：B 解答を投票する

質問 3

A consultant finishes creating a new ESXi cluster. The consultant connects to the nodes via laptop and a personal flat switch. The host/CVM network is on VLAN 23. The customer has the native VLAN on the ToR switches set to 23.
The customer wants to use LACP. Before placing the nodes on the customer network, the consultant tags VLAN 23 for each host and CVM. The consultant connects the nodes to the customer network and finds that they are unreachable.
What is causing this issue?

（A）The host and CVM are incorrectly configured.

（B）The hosts have not been migrated to a vSphere Distributed Switch.

（C）Under the vSwitch0 settings, the consultant did not select Route based on IP hash.

（D）The customer has LACP fallback enabled on switch ports.

正解：B 解答を投票する

質問 4

A customer wants to expand an existing cluster with three additional nodes. After running the Foundation process on the new nodes, the customer realizes that the wrong IPs where used and the nodes are configured on a different network. The customer decides to create a new cluster instead.
Which method should be used to recreate the cluster?

（A）Log into Hypervisor and use cluster create command to create the cluster.

（B）Foundation all nodes again and create the cluster.

（C）Log into CVM and use cluster create command to create the cluster.

（D）Log into IPMI and use cluster create command to create the cluster.

正解：C 解答を投票する

質問 5

A consultant is installing Nutanix AOS on Cisco UCS.
Which method should be used to install AOS on UCS hardware platforms?

（A）Foundation Applet

（B）Foundation VM

（C）Foundation as a Service

（D）Foundation Central

正解：B 解答を投票する

質問 6

Where in the Support Portal is the Best Practices guide for vSphere Networking located?

（A）Product Notices

（B）Knowledge Base

（C）Solutions Documentation

（D）Software Documentation

正解：C 解答を投票する

質問 7

After imaging the nodes and creating the cluster successfully, the consultant connects the cluster to the customer network. When logging into Prism, the events dashboard is full of errors.
What is causing the issue?

（A）The cluster was not stopped prior to connecting to the customer network.

（B）Foundation did not create the cluster successfully.

（C）The consultant did not run Nutanix Cluster Check (NCC..

（D）The Cluster Virtual IP Address (VIP) was not set up during the process.

正解：A 解答を投票する

質問 8

A consultant is setting up a new vSphere cluster. Customer requirements are as follows:
* VMs should automatically failover to another host if the host crashes
* Host CPU and Memory resources should be evenly balanced
* New VMs should be placed on the host with the most resources available Which two settings should be turned on to meet the requirements? (Choose two.)

（A）vShpere DRS

（B）vSphere vMotion

（C）vSphere HA

（D）vSphere Power Management

正解：A、C 解答を投票する

NCSC-Level-1 無料問題集「Nutanix Certified Services Consultant (NCSC): Level 1」

弊社を連絡する

関連リンク

トップ試験